ALL OF OUR WIGS ARE AS LONG AS WE CAN POSSIBLY GET, GENERALLY BETWEEN 7" AND 10" IN LENGTH, DEPENDING ON WHICH COLOR YOU NEED.THESE ARE WONDERFUL WIGS AND WE CAN'T SAY ENOUGH GOOD THINGS ABOUT THEM. THEY ARE THICK AND FULL AND WILL MAKE YOUR BALD OR THINNING TROLL POP BACK TO LIFE.
EACH WIG IS .00 PER 2" BY 2", WHICH FIT THE FOLLOWING TROLLS:
- ALL 2 1/2" & 3 " TROLLS
- 3" DAM HORSES (RECOMMEND ONE AND A HALF WIGS FOR FULL LOOK)
- 3" SITTING ELEPHANT
- 3" SITTING DONKEY
- 2 1/2" AND 3" TAILED TROLLS
- 3" AND 6" COW TROLLS
- 5" DAM AND WISHNIK TROLLS
- 1964 DAM CLOWN WITH BAGGY TROUSERS
WE CAN ALSO CUSTOM CUT WIGS TO FIT MOST ANY SIZE TROLL, FROM SMALL SCANDIA PENCIL TOPPERS, TO 12" IGGY'S.
Email Dave or Leigh-Ann for more info by clicking here
COLORED WIGS ALSO AVAILABLE BY SPECIAL ORDER.
Email GOOD LUCK CHARMS
WIG GLUING TIPS FOR SMALL 1960's TWO AND ONE HALF INCH AND THREE INCH TROLLS
RECOMMENDED SUPPLIES FOR THE TASK:
- PENCIL W/ ERASER
- SCISSORS
- CLEAR VINYL GLUE (FOUND AT HOME IMPROVEMENT STORES) OR TACKY WHITE GLUE , AS IT CAN BE LOOSENED WITH WATER IF YOU DO NOT LIKE THE WIG DOWN THE ROAD.)
- SMALL SCRAPING TOOL, LIKE A BUTTER KNIFE OR SOMETHING THAT YOU CANNOT HURT YOURSELF ON. (IT IS SUPER EASY TO SKIP AND CUT YOURSELF)
~ LOTS OF FOLKS DO NOT EVEN GLUE WIGS INTO PLACE, THEY JUST SET THEM INSIDE THE HEAD. THIS WORKS WELL, BUT FOR THOSE WISHING TO HAVE THE HAIR GLUED IN (WE ALWAYS DO, IT KEEPS THEM ORIGINAL LOOKING AS POSSIBLE.)~
PREP WORK: ONCE YOU HAVE GOTTEN RID OF ANY OLD HAIR, THE KEY TO GETTING A GOOD GLUING AND TO MAKE YOUR TROLL LOOK AS GOOD AND ORIGINAL AS POSSIBLE, YOU NEED TO SCRAPE ALL OF THE OLD GLUE AND HAIR RESIDUE FROM THE HAIRLINE OF THE TROLLS HEAD. THIS CAN BE DONE WITH MAYBE A BUTTER KNIFE OR REALLY SMALL SCRAPING TOOL. PICK A QUIET TIME AND GO SLOWLY, YOU CAN USUALLY GET GREAT RESULTS. JUST TAKE YOUR TIME AND BE CAREFUL NOT TO SLIP AND SCRATCH THE TROLLS FACE.
WIG GLUING IN THREE EASY STEPS!
TAKE YOUR WIG AND FOLD THE LEATHER IN HALF, UP AGAINST THE MOHAIR. FOLD IT AROUND AGAIN MAKING IT A CONE SHAPE (IF IT FEELS TOO BIG, YOU CAN TRIM THE LEATHER DOWN WITH SCISSORS, BUT YOU MAY LOSE SOME HAIR VOLUME.)
- SHOVE THE WIG INTO THE PREPPED AND CLEAN CAVITY OF THE TROLLS HEAD, BUT BE VERY CAREFUL OF THE WIRES FOR THE EYES AS THEY CAN SNAP OFF REAL EASY SOMETIMES IF THE WIRES ARE RUSTY, AND CAUSE THE GLASS OR EVEN PLASTIC SPIRAL EYES TO BREAK.
USE YOUR PENCILS ERASER SIDE TO PUSH THE WIG INTO PLACE SNUGLY, MAKING SURE THAT NONE OF THE LEATHER ON THE HAIR IS EXPOSED OR SHOWING.
- TIME FOR GLUING. THIS VINYL GLUE WE RECOMMEND IS EXACTLY LIKE WHAT DAM USED IN THEIR FACTORIES, IT CAN BE MESSY AND YOU MUST GO SLOW BECAUSE IT DRIES IN MINUTES. ALSO KEEP IN MIND THAT IT DOES HAVE A STRONG GLUE ODOR, SO BEST TO DO THIS IN A WELL VENTILATED AREA.
IF YOUR LEATHER IS IN A CONE SHAPE, YOU ARE READY TO GLUE, PUT A COUPLE OF DROPS ON THE INSIDE OF THE HEAD AROUND THE NECK/CHIN AREA THAT STICKS OUT. SHOVE THE WIG IN WITH YOUR PENCIL, AND YOU SHOULD HAVE A NICELY GLUED WIG. DO NOT MOVE THE WIG AROUND AFTER GLUING, SO KNOW WHICH WAY YOU WANT TO HAVE IT GO IN BEFORE GLUING INTO PLACE.
GLUING AROUND THE HAIRLINE IS NOT RECOMMENDED UNLESS YOU HAVE LOTS OF EXPERIENCE AND/OR A LOT OF TROLLS AND HAIR TO PRACTICE ON. WITH THE GLUE AT THE HAIRLINE, IT IS SUPER EASY TO GET GLUE IN A VISIBLE AREA OR EVEN ON THE TROLL, AND THIS CAN DEFINITELY DEVALUE YOUR TROLL IF THE GLUING IS NOT DONE CORRECTLY.
STILL HAVE QUESTIONS? WE'RE HERE TO HELP, EMAIL US BY CLICKING HERE, FOR FAST AND FRIENDLY TROLL HELP
|
|